CMP / Keller©
Boat Racing Hardware
Boat Rigging
(Prices subject to change without notice.)
171,
Bow Handle, light weight, cast aluminum, black powder coat satin finish, sanded accent highlight stripe,
comfortable grip, 3 #10 stainless steel wood screws included, $16.95 each.
176B, Transom Handle, open base (two handles shown), comfortable grip, light
weight, cast aluminum, black powder coat satin finish, sanded accent highlight stripe,
stainless steel bolts, nuts (Order 176S for same transom handle
with stainless steel wood screws. Bolt pattern center-to-center is 1"
x 5-7/8". Holes drilled and countersunk for #8 oval head bolts.), $17.95 each.
174B, Transom Handle, closed base (two handles shown), comfortable grip, light
weight, cast aluminum, black powder coat satin finish, sanded accent highlight stripe,
stainless steel bolts, nuts (Order 174S for same transom handle
with stainless steel wood screws.), $17.95 each.
202, 2-Wire Connector, 16 gauge red and black wire, 12" long,
2-wire flat "trailer" style pull-apart connector, use in wiring
harness to disconnect motor from kill switch circuit when motor is removed, $4.95 each.
205, Kill switch for magneto, for use on magneto systems only (circuit is
closed when tether is pulled), mounts through dash, cockpit side, or floor board
through 5/8" diameter hole up to 3/8" thickness, wire leads, nylon
tether line approximately 3' long connects switch clip to life jacket clip, some
magneto systems may require a kill switch for each coil, $16.95 each.
206, Kill switch for ignition (battery), for use on ignition (battery)
systems only (circuit is opened when tether is pulled), mounts through dash, cockpit side, or floor board
through 5/8" diameter hole up to 3/8" thickness, wire leads, nylon
tether line approximately 3' long connects switch clip to life jacket clip, $16.95 each.
208, Kill switch with coiled lanyard for magneto or ignition (battery), can be configured to
open or close circuit when lanyard is pulled, mounts through dash, cockpit
side, or floorboard through 5/8" diameter hole up to 3/8"
thickness, uses standard automotive spade connections for wire connections (not
included), coiled lanyard (approximately 14" when coiled, approximately
48" when stretched) with switch clip and life jacket clip, $22.95.
209, Coiled lanyard, coiled lanyard (approximately 14" when
coiled, approximately 48" when stretched) with switch clip and life jacket
clip, for use on 205, 206, 208, or 210, $7.95.
210, Dual-Input Kill Switch Kit, used to allow two separate ignition
sources to be grounded through one single kill switch. The two separate
ignition sources may be two separate ignition sources on a multi-cylinder
outboard such as the Yamato 302 or may be two separate outboards such as
a dual outboard installation. Kit includes kill switch, dual-input diode,
lanyard, and wiring instructions, $47.95
212, Magneto kill switch wiring harness, for use on magneto systems only (circuit is
closed when tether is pulled), kill switch mounts through dash, cockpit side, or floor board
through 5/8" diameter hole up to 3/8" thickness, 8' wiring harness
(specify length when ordering if different from 8') contained in black ribbed
flexible plastic shielding, internal wire connections are heat shrink sealed, 2-
wire connector to disconnect motor from boat, nylon tether line approximately 3' long connects switch clip to life jacket clip,
$47.95 each. Custom wiring harnesses for ignition-type kill switches or
dual-input diode set-ups also available. Contact Portage Bay Systems for
pricing on custom harnesses.
2N, Transom pad (two shown), machined aluminum, to protect front side
of transom from motor clamp pads, also aids in centering motor on boat, 4"
high by 3" wide, pad area is 3/16" thick, pre-drilled for #8 oval head
stainless mounting wood screws (included), $16.95
each.
2E, Eye-bolt, Machined AISI 304 stainless steel closed loop welded eye-bolt. May
be used for motor tie-down or bow eye, approximately 5/8" ID eye, 8mm x 3"
bolt, 1" diameter flange and backing washer, 8mm nut, $10.95 each.
2T, Transom Plate, dimensions: 10" x 10" x 3/16", 6061
aluminum plate, to protect rear side of transom from motor clamp bracket, plate
is without pre-drilled holes as hole requirements differ by application, four #8 flat head stainless mounting wood screws
are included, $16.95.
BP, Boat Padding, 1" thick, charcoal gray color, lightweight, closed cell
foam. Available in full 40" x 80" sheet or custom cut to
size. Full 40" x 80" sheet, $89.95. Custom cut to size,
$0.04 per square inch. Example: 16" x 36" = 576 sq. in. x
$0.04 per sq. in. = $23.04.
Some
items are only available on special order.
